Pertains to all trucks and their systems except: a) trucks solely guided by mechanical means (rails, guides, etc); b) trucks operating in areas open to persons unaware of the hazards.
This part of IEC 60204 applies to electrical, electronic and programmable electronic equipment and systems to machines not portable by hand while working, including a group of machines working together in a co-ordinated manner.
Defines electrical and related mechanical safety requirements for design and construction of the electrical installation in battery powered industrial trucks hereinafter referred to as trucks, with nominal voltages of the truck system up to 240 V.
Gives perspectives on wireless network of data acquisition terminals, robotic type equipment or automated guided vehicles, and Robotic arms
The document provides an overview of ETSI activities linked to StandardizationNeeds in the area of "Robotics and Autonomous Systems" (RAS), referred to as a “multidisciplinary scientific and technological domain for implementing complex systems with cognitive capabilities” (see the EU ICT Standardization Rolling Plan)
Presents a study of use cases and vertical scenarios for Ultra-Reliable Low-Latency Communications (URLLC) intended to be used as base requirements for evolving DECT. Applications / Use Cases include Home and Building Automation, including Smart Living; Industry automation - Factories of the Future, Industry 4.0; Mobile robots
robot. programmable device capable of carrying out a series of actions automatically. fr. robot, m. dispositif programmable capable d'effectuer une série ...
IEC 60068-2-64:2008+A1:2019 demonstrates the adequacy of specimens to resist dynamic loads without unacceptable degradation of its functional and/or structural integrity when subjected to the specified random vibration test requirements. Broadband random vibration may be used to identify accumulated stress effects and the resulting mechanical weakness and degradation in the specified performance. This information, in conjunction with the relevant specification, may be used to assess the acceptability of specimens. This standard is applicable to specimens which may be subjected to vibration of a stochastic nature resulting from transportation or operational environments, for example in aircraft, space vehicles and land vehicles. It is primarily intended for unpackaged specimens, and for items in their transportation container when the latter may be considered as part of the specimen itself. However, if the item is packaged, then the item itself is referred to as a product and the item and its packaging together are referred to as a test specimen. This standard may be used in conjunction with IEC 60068-2-47:2005, for testing packaged products. If the specimens are subjected to vibration of a combination of random and deterministic nature resulting from transportation or real life environments, for example in aircraft, space vehicles and for items in their transportation container, testing with pure random may not be sufficient. See IEC 60068-3-8:2003 for estimating the dynamic vibration environment of the specimen and based on that, selecting the appropriate test method. The major changes with regard to the previous edition concern the removal of Method 1 and Method 2, replaced by a single method, and replacement of Annex A with suggested test spectra and removal of Annex C. Also included in this revision is the testing of soft packed specimens.
IEC 60068-2-2:2007 Deals with dry heat tests applicable both to heat-dissipating and non heat-dissipating specimens. For non heat-dissipating specimens, Tests Bb and Bd do not deviate essentially from earlier issues. The object of the dry heat test is limited to the determination of the ability of components, equipment or other articles to be used, transported or stored at high temperature. These dry heat tests do not enable the ability of specimens to withstand or operate during the temperature variations to be assessed. In this case, it would be necessary to use IEC 60068-2-14 Test N: Change of temperature. The dry heat tests are subdivided as follows:- Dry heat test for non heat-dissipating specimens with gradual change of temperature, Bb.- Dry heat tests for heat-dissipating specimens with gradual change of temperature, Bd. with gradual change of temperature, specimen powered throughout, Be. The procedures given in this standard are normally intended for specimens that achieve temperature stability during the performance of the test procedure. The main changes from the previous edition are as follows: Tests Ba and Bc have been deleted since they were more severe tests than Test Nb, IEC 60068-2-14: Change of temperature. Secondly it was considered justified to delete the 3 % value on the temperature difference between the chamber air and the wall temperatures. Thirdly it is proposed that the test specimen be powered throughout the test where required; and, finally, the annexes have been removed.
This document provides guidance on the practical application of safety and lean manufacturing principles to machinery and manufacturing systems for improving performance, safety and quality by reducing injury and waste. The guidelines in this technical report assist machine tool users to minimize waste and risk associated with machinery and manufacturing systems, including individual and integrated machine tools and auxiliary components.
This Technical Report introduces three categories of inspections; conversational inspections, visual inspections, and technical inspections. Applying the appropriate category to existing inspections improves communication, safety culture, and risk reduction measures. Although each of the three categories provide a benefit, it is not necessary for all categories to be used. The template checklists which are included may be modified to produce “organizational specific” checklists by either internal or external subject matter experts